By this time, the front-wheel drive and the hatchback-type body have become commonplace on this car. Do it yourself and use this 2002 Volkswagen Passat repair manual software to guide the way. Ensure that the jaws of the pliers seat in the -arrow -B- of the clamp. Serial production of the Passat B3 was completely stopped in 1993. The three- and five-door hatchback and station wagon were manufactured in North America for and during the 1974 model year.
Note: The protective seal outer sealing lip will then locate in the piston groove. Platform B2 is again based on the corresponding platform , launched in 1978. This sharp Sports Utility Vehicle is available with the latest clean diesel technology or even a gas electric hybrid configuration. Steering gears that are damaged by an accident must be replaced For a satisfactory and successful repair, the greatest care, safety and proper tools are required. Passat B3 The third generation Passat debuted in Europe in 1988, in North America in 1990 and in 1995 in the South. Illustration shows the housing in cross section for better view.
Make sure plier jaws seat in grooves of clamp arrows -B- - Tension clamp by using torque wrench to turn spindle keep pliers at right angle to shaft. Note: Chamfer on inner diameter of ball hub splines must face the contact shoulder on the drive shaft. The interior is slightly different from the B6, the main design of the instrument panel remains unchanged. The lower part of the body of the Syncro version was completely different: a central tunnel for the transmission was introduced, the fuel tank was changed, there was no spare wheel to make room for a complicated rear axle. Page 5 of 5 45-5 Wheel speed sensor and rotor for speed sensor, removing and installing Speed sensor When installing speed sensor ensure wiring is not twisted.
Passat B1 The first generation of the Volkswagen Passat was launched in 1973. A restyling dashboard in the Golf style was used, the radio and heating control systems were installed centrally in one unit. In August 1975, the 1. The model was called Passat in all markets. Install steering wheel Page 48-9 Install airbag unit. Adjust with engine switched off.
It is produced since 1973. Ib New belts, 7 Nm 62 in. Illustration shows the housing in cross section for better view. On March 31, 1988, the production of Passat B2 was over although the Syncro models were produced until June. Use a bleeder bottle or a plastic bottle which is only used for brake fluid. Note: The 6 balls of each joint belong to one tolerance group. Tightening torque: 10 Nm 7 ft lb Fig.
These cars have ignition coils that… Water4gas exposition and hho games held in south Florida on November 11th. This generation of the Passat had only 2 body styles: a four-door sedan or a five-door wagon. Do not reuse drained hydraulic oil. Note: Grease all mountings before installing with G 000 602 grease. Removing - Before disassembling mark position of the ball hub in relation to the ball cage and housing with an electric scriber or oil stone.
If piston is difficult to move, use a 13 mm open end wrench on flats arrow A provided for this purpose. Removing left-side drive axle - Set up engine support bridge. For anti-theft coded radios, first make sure that the radio code is available. With the Haldex system, during normal driving, the car behaves as a front-wheel drive, until an axle slip is detected. All models were restyled in 1977 in 1978 outside Europe , with interior upgrading and redesigned design, depending on the model: four round headlights, or two rectangular.
While there are few nations on earth that have such a reputation, and a well-deserved one at that, for automobile manufacture, that is not to say that you will never have a problem with a Volkswagen. The issue was stopped in 1996. Fill the pump with G 002 000 hydraulic oil and rotate it by hand, otherwise the pump may be damaged or. If complaints are received determine cause with the help of pressure tests, leakage test and troubleshooting programs. Do you know how to fix your ignition coil without shelling out money for a mechanic? In July 1978, Passat Diesel appeared equipped with a 1. Note: After each brake pad change firmly depress brake pedal several times with vehicle stationary, so that the brake pads are properly seated in their normal operating position. It was the first cross-motor Passat, built on its own platform Volkswagen, which has nothing to do with the platform B3 Audi.
Therefore note the following points: Install oil seal and grease cap as shown. Check for cracks and abrasion Before tightening the small clamp, ventilate boot briefly so pressure is equalized, Fig. Removing and installing suspension strut at body Page 42-4 Tightening torque -A-: 65 Nm 48 ft lb Note: Support control arm otherwise damage may occur to. Front brake disc thickness Pad thickness Rear brake caliper dia. On Diesel engines an exhauster is installed to create the required vacuum. Getting the same information in digital format is so much less expensive and more convenient! Specification: Used belts, 4 Nm 35 in.