View of the electrical connections on the back of the cluster To install: Connect the electrical wire harness plugs and install the instrument cluster. Holding the cooling tube aside, pull the blower motor and wheel from the heater blower assembly and remove it from the vehicle. If it lands in your eyes, get medical help immediately. In some instances, the Transaction confirmation may serve as your receipt and the Transaction also will appear on your card or account statement. Position the bracket, with the power steering pump attached, to the engine. Remove the oil pan as described under Oil Pan removal and installation.
Remove the motor mount nuts from the frame. To install: Connect the wiring and slide the radio into the instrument panel. There is a separate access panel that unbolts from what would be considered the oil pan which is now known as the ladder frame. Lubricate all rocker arm assemblies with heavy engine oil. Your use of the how-to videos is at your own risk and we are not liable for any damage to your vehicle or injuries to you or any third party based on your use of the videos. Otherwise, continue with the procedure to also remove the lower intake manifold. The Econoline is a very popular choice for fleet users and 95% of the Econoline is being purchased fleet uses.
Aluminum can also use the tapered inserts, however welding is the preferred method. For premium starter motor function, the resistance in the starting system must be kept to an absolute minimum. Install the fuel supply and return line assembly. This will prove fatal in sufficient quantity. Carefully pry the crankshaft toward the rear of the engine and hold it there while you zero the gauge. Through a collection of current features, and features coming soon, FordPass will provide you with more mobility options so you can go further than you thought possible. Remove the distributor and fuel pump.
Remove the switch from the transmission. However, it is not necessarily the best, and in some cases, a knurled valve guide will not stand up for more than a short time. Make sure to label them to assure proper installation Detach the accelerator and speed control if equipped cables from the throttle body lever. Runner lengths are tuned to optimize engine torque and power output. Tag and disconnect all electrical wires attached to the upper manifold assembly. General Information These Terms apply to your access to and use of the FordPass.
Make sure the injector caps are clean and free from contamination or damage. The injectors do not need to be removed unless a new manifold is being installed Click to enlarge Lower intake manifold removal on the 2. Unless and to the extent local law requires otherwise, these Terms are governed by, and construed in accordance with, the laws of the State of Michigan, except in relation to any conflict of law provisions thereof. Failure to conduct maintenance and repairs in a safe manner may result in serious personal injury or death. Gloves and eye protection are required. Extreme care should be take not to mix or substitute components. If a court determines that any term or condition is illegal, invalid, or unenforceable, then such term will be eliminated and the remaining terms and conditions will remain in full force and effect.
Disconnect all of the hoses from the sensor. Raise and support the vehicle safely. If the lamp does not illuminate, skip to Step 4. Some features may only be available through the Site or through the App. It is advisable to wash the windshield carefully with a commercial glass cleaner at least once a month.
To remove the blower motor, first disconnect the electrical wire harness plug. Pull out the dipstick and note the oil level. Remove the drive belt tensioner. Oil pan installation on the 4. Relieve the fuel system pressure. Before the camshaft can be removed, all of the followers must first be removed. Certain state and local authorities have requirements for headlight aiming;.
They even show you how to change the light bulbs. When the coupling is connected together, the flared end of the female fitting slips behind the garter spring inside the cage of the male fitting. Drain the oil from the crankcase. If a distributor is not keyed for installation with only one orientation, it could have been removed previously and rewired. The gauge should slide freely around the entire ring circumference without binding. Installation is the reverse of removal. Make sure that the timing marks are still aligned.
Open the ash tray and remove the two retaining screws. Loosen the water pump pulley attaching bolts. If the valves are in extremely good condition, as well as the valve seats and guides, they may be lapped in without performing machine work. Install the distributor into the engine. Install the belts and tension them. Install the power steering pump.
Installation is the reverse of the removal procedure. Do not damage the sensing element or possible failure of the sensor may occur. If you believe that there is an error or unauthorized Transaction activity, you agree to contact us immediately. FordPass may integrate with other services or features that are subject to different privacy policies as described in connection with those services or features. If the battery were shorted to ground, the alternator would also be shorted. For ladder frame removal procedures, refer to the oil pump removal and installation procedure in this section. Payment features may not be available during maintenance breaks and other times.