There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in. Nov 25, 2013 Check that you have the correct bulbs in the tail light sockets. Sometimes working on wiring is difficult if the mechanic is colorblind. Identify where the retainer studs and sliding clips are on the tail light before removing it. But when i want pull and uninstall.
There aren't seem to be a lot of picture tutorial on how to remove the headlight on the web, I decided to write my own detail picture tutorial and share it with you guy. Entering your vehicle information in our Year Make Model selector up top, helps ensure you get an auto part that fits your car, truck or other type of vehicle. On my 99 cougar they had to bypass this module because the modules kept going out. If you not sure the shipping cost, pls send email to us. I ordered this as a replacement because my original developed a leak and would fill with water when it rained. Some of the later vehicles use separate stop and turn bulbs.
I had a similar problem on my Nissan Sentra. Picture are taken with my phone so the quality isn't that good. Also don't mind the grammar as English is my second language. Here's a quick guide to changing the Taillight bulb on a 2006-2013 Nissan Versa Hatchback. We love when auto parts experts come to our site and we love when car parts newbies come to our site. On top of low prices, Advance Auto Parts offers 3 different trusted brands of Tail Light Assembly products for the 2013 Nissan Versa. Some of the other bulbs in the tail light cluster such as the brake light or turn signal may also function as the tail light in your Versa.
Then this harness runs as 1 piece all the way to the rear bumper. Note:Plaese tell us the model and year of your car before purchase. Be careful not to damage the white nub as it helds the headlight in position This is what it look like when you remove the headlight Replace the light bulb by twist it counter clockwise. Insert the rope between the headlight like the pictures shown Grab the both rope, apply equally moderate amount force to both hand and pull it out. Have parts delivered straight to your home, or find the nearest Advance Auto Parts store to check out our Tail Light Assembly stock in-person! The loss of signal is suppose to keep the Vehicle in Park. Improper wiring could burn out the flasher units.
Fitment:For Nissan versa 11-14 Position:Transparent Front Headlight lampshade Left Side Cover Direct replacement Built to strict quality control standards Remote areas need to pay extra shipping fees. I had searched a few places locally for a tail light cover for my jeep, and also searched online. I couldn't have done it without them! But it does line up and bolt on securely and performs it's function just fine. All replacement lamps are manufactured and rigorously tested for quality, fit and function. Please check and confirm this things fits yours before buying. Brake light bulbs grow dimmer over time and eventually burn out.
Slowly pry very slightly under the Taillight until it starts to move away from the body. Remove the screws and pull the bottom out and the top is held in by two retainers that should just slide right out Posted on Oct 13, 2009 I changed my wife's last night and there is no need to take the tail light housing out. Separate flashers create the pulse to flash the lights. Or you may just be struggling to keep it highway-approved. Please check and confirm this things fits yours before buying.
It is really stuck in there but will give way. That's is it but it can be quite a pain if you don't use the rope as a leverage to yank it out. Disconnect the connectors from the taillights taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps. The only vehicles that do not require a converter box are the vehicles that use the stop lamp bulb as a turn signal. Both the hatchback and sedan have 2 studs that stick out into plastic clips on the car body. Tools you are going to need: 2 short flat rope or thick string paper towels flat head screw driver wrench First locate the 2 covers Pry it open using the flat head screw driver. Nissan has holes in the body to access the tail light bulbs that may make the bulbs too difficult to remove without removing the whole tail light.
I have taken it off before but you do not need to access the light. All of the stop lamps are on the same circuit. The white wire in the trailer harness is for a ground when used on a trailer. Sep 05, 2011 It is all related and the connections should be undone immediately. On some vehicles there is a brake module that causes the tail and brake lights to go out. Some of the Electronic light flashers can sense how many bulbs are in the circuit to maintain a steady flashing rate with or without a trailer hooked up.
I was kind of concerned because there are exposed wires above the plug, as in the photo. Start at the bottom then the middle of the Taillight. Once pry it open, use the paper towl and cover the nearby area to prevent the screw from falling in when you unscrew the nut. This article has also been viewed 52,581 times. Hello, So--there are several things I am thinking here.