We have worked hard to design a site that caters to everyones Mini Cooper Tail Light needs. Protect your eyes, hands and body from fluids, dust and debris while working on your vehicle. Now you can replace the bulbs and tail light assembly. Step 2 — Loosen the Torx screws With the trim ring removed, you can now access the three Torx screws holding the housing in place. That's why it's a legal requirement to have good tail lights.
I got a replacement sensor from a mini breakdown outlet £20 so don't pay bmw prices, the garage replaced the broken one just wear and tear he said, by removing the bumper and poping out the damaged sensor and replaced the new one. Unlatch the back of the top and lift it up. Push in the two clips as you push out the tail light assembly. If you want to try to replace the bulbs from the interior follow the next few steps. Cant wait to see Tigger with his new lights, hopefully you will get a warm spell! I finally got my butt to the Do It Yourself garage needed heat and decided to switch out the tail lights. It's fastened to the vehicle with a single long bolt and nut.
Your tail lights may not seem all that important to you, but they are very important for other drivers. Is there any way to just get the carrier shown on the Part : 63-21-7-255-913-M26 tail light assembly? Step 2 — Install the new tail light assembly Press the bulb board to the back of the new tail light assembly until it snaps into place. Loosen each Torx screw and make sure to place them in a safe place. Figure 9 Replace the bulbs as needed. On one side of the tail light assembly there are two clips. The new tail lights include the back up lights and the bottom light is off set.
Pro Tip Make sure you are not putting too much stress on the ring, as it should easily pop off. November 2, 2016 Followup from the Pelican Staff: Thanks for the feedback. Many owners tend to prefer the clear look, so the quickest solution is to find aftermarket lenses to replace them. In 2005 they changed the tail light design even though the exterior dimensions stayed the same. If other drivers around you aren't aware of your braking and turning, it could quickly lead to an accident. This article applies to the 2nd Gen Mini Cooper. Click here to replace it.
I wouldn't have had the confidence to force the trim off and the light assembly out without your instructions and pictures. This article applies to the Mini Cooper. Just slide it in on the upper side of the trim ring, and gently pry around the headlight until it pops off. It is held in by a 10mm nut and two tabs. Now, I have a set of tail lights that really won't work for my car. With your vehicle info, Give The Pelican Parts parts specialists a call at 1-888-280-7799. Tried bulbs not the bulb holder.
I dismantled the interior and eventually removed the bulb housings. The workspace is tight, and it is easy to drop a bulb into the body. Line up the tail light assembly to the opening in the Mini, then press it in until it snaps into place. When dealing with bulb failures or bulb out messages, always inspect the electrical connector and taillight bulb holder. Use these instructions to learn how to easily remove your stock tail lights. My mechanic said that the connection for the bulbs are not functioning and I need to purchase an entire new light fixture. Locate the black tab on the back and push it in to release the bulb board from the rest of the tail light assembly.
Valeo is a global company that engineers thermal, powertrain and other automotive systems with emission reduction and intuitive driving in mind. The pulses are too short to illuminate bulbs but serve the purpose of evaluating whether an individual bulb or bulb circuit is defective. On the back of the assembly you'll see the back of the bulb board. Burn out tail lights are a common reason for a police officer to pull you over, so we recommend changing all of the tail lights on your Cooper whenever one is burnt out. Working in the trunk on the side, pull the access panel out yellow arrow. We're here to help you find that perfect Tail Light for your Mini Cooper.
I'm thinking that's not a good idea. This article applies to the 2nd Gen Mini Cooper. Never work on your vehicle if you feel the task is beyond your ability. Remove the T15 Torx screws. They can figure out what part or repair kit you need. Whether you want to replace your stock lenses or customize the originals, removing your tail lights is actually very simple. Then rotate the bulb holder 45° counterclockwise to remove inset the bulb.